Operation Manual  
VER V1.0.20-10-B853  
2015/10/13  
BlueEyes iCam PRO Full HD Camera  
Thank you for using the product of BlueEyes Technology.  
The manual will introduce the product of BlueEyes Technology. Please read the manual  
before you start using the product.  
Though the information in the manual has been verified before publish, the actual  
specification should be based on the actual shipment. BlueEyes Technology doesn’t  
have to guarantee, proclaim or declare for the content, along with other purpose. In  
addition, the product specification and information that mentioned in the manual is for  
reference only. The content might be update at any time without notice. If there is any  
mistake of the information, including software, firmware, and hardware that mentioned  
in the manual BlueEyes Technology has no responsibility for the mistake.  
Please reach BlueEyes website to get the upgrade of the product specification, our  
company will not notice you. If you want to get the latest product information, operation  
manual, firmware, or you have any question to the products of BlueEyes Technology,  
please contact your local agent or go to the official website of BlueEyes Technology for  
further information.  
It is not allowed to copy/ use the content or to change the information and publishing of  
the manual without BlueEyes Technology’s written consent.  
Copyright 2015 BlueEyes Technology Inc. All Rights Reserved.  
BlueEyes Technology Corp.  
Add: 7F-3, No.200, Sec. 4, Wenxin Rd., North District, Taichung City 40462, Taiwan  
TEL: +886 4 2297 0977 / +886 982 842 977  
Website: www.BlueEyes.tw  
BlueEyes Technology  
1
www.BlueEyes.tw  
 
BlueEyes Technology  
2
www.BlueEyes.tw  
BlueEyes Technology  
3
www.BlueEyes.tw  
Most of the recording systems use traditional security camera, so the quality  
was very bad. The students have to look closely to see the words on the  
blackboard. This kind of camera is not suitable for education institute  
environment.  
BlueEyes Technology develops the Full HD Camera especially for the  
education institute environment and registers the trademark as iCam® . Now  
we have iCam PRO. It not only reserves the high quality of shooting, but also  
upgrades the sound receiver which build-in camera and have the best  
distance---38 mm between two microphones. In order to enhance the  
characters on the whiteboards, digital boards, and projectors, iCam PRO can  
detect the external environment automatically and make the characters  
clearer. Watching the iCam PRO videos is like watching Blu-ray movies in the  
movie theaters.  
PS: iCam PRO is unlike normal camera, it is designed for education institute  
environment with full HD camera.  
BlueEyes Technology  
4
www.BlueEyes.tw  
 
 
 
More information and features, please check official website of BlueEyes  
BlueEyes Technology  
5
www.BlueEyes.tw  
 
Please do not leave or install the device in damp, direct sunlight, hot or confined  
spaces.  
Do not put anything that would fall into the machine on top of the machine.  
Do not place the machine on an unstable place. It may fall down, resulting in an  
injury.  
Please use this machine in a place with good ventilation. Do not block the heat  
dissipation vents. Poor heat dissipation can lead to a rise internal temperatures  
and cause malfunctions  
Use dry rag to clean the machine. Do not use solvent.  
We will not be liable for any damage caused by the use of third party power  
supplies in this machine  
Never plug the machine into a power socket that is shared with other equipment  
(
extension load/cord, 2- or 3-way adapter, etc.). This may result in fire or electrical  
shock or fire.  
To prevent the machine from thunder, please make sure there is a ground  
connection.  
Please do not disassemble, re-design or maintain the device by yourself.  
The processors and accessories all pass the safety test of CE and FCC.  
Please turn off iCam PRO, including power, network, sound  
and video to avoid the damage from thunder. According to  
BlueEyes warranty rules, thunder is one of natural disaster  
BlueEyes Technology  
6
www.BlueEyes.tw  
 
-
- Back panel --  
Back panel descriptions:  
DC12V  
LAN  
DC12V power input.  
Attach the provided RJ-45 cable and the port is auto-sensing and supports negotiations  
at 10/100 speeds.  
VIDEO  
Connect to video equipment, such as a monitor or projector.  
Connect to an audio input source.  
LINE IN  
Do not test or connect the interface not commonly used. It  
may cause instability of the system.  
BlueEyes Technology  
7
www.BlueEyes.tw  
 
 
Fixed iCam PRO camera diagram:  
Scanning iCam PRO camera diagram:  
The small monitor can suck on the direction controller. If you worry that it is not  
steady enough, you can stick directly on the monitor.  
There are two control buttons on the direction controller of the scanning iCam PRO  
camera, and the left and right controller is for SES. If you worry that the students  
might drop it on the floor, you can stick it on the table with double-sided tape or  
silicone as some of the education institutes do.  
Use flexible wire for network cable, video cable and audio cable to avoid fixed  
screw loosening or interfaces dropping after long use.  
Put termination plug at the end of the left and right turn.  
After installing, you must rotate to the end and see the image simultaneously to  
make sure the cables would not be pulled or the fixed screw of the camera would  
BlueEyes Technology  
8
www.BlueEyes.tw  
 
 
not loosen when rotating.  
Use [double tone] for audio cable.  
Follow these steps to watch live video on the notebook:  
1
2
3
4
. Open Microsoft Internet Explorer(IE) browser.  
. Enter the camera IP (192.168.1.171-176) on address bar.  
. Enter username and password.  
. Choose “Live View” to watch the video.  
The operator username is sesuser. As a default, check the  
factory configured list. You can edit account name or  
password in setting. We recommend using Microsoft  
Internet Explorer version 10 or higher web browser.  
BlueEyes Technology  
9
www.BlueEyes.tw  
 
The height of center blackboard is the best location.  
Higher than the students.  
Lower than the upper side of the blackboard  
Better install on the wall at the back of the classroom.  
Viewport of the location of camera  
If you didn’t install the camera at the location aimed the center of the  
blackboard, the blackboard would show as a trapezoid.  
BlueEyes Technology  
10  
www.BlueEyes.tw  
 
 
Elevation of the location of camera  
If you install the camera too high, the blackboard would show as a trapezoid,  
the bottom is shorter than the upper side.  
BlueEyes Technology  
11  
www.BlueEyes.tw  
8
.5-50mm les  
2
.8-8mm les  
Please loosen the nuts on the lens before adjusting the lens. But please do  
not remove it or it may get lost.  
The adjust order is  
IRIS(O←→C)  
Focal distance(W←→T)  
Focus(∞←→N)  
O = Open, C = Close  
IRIS controls the light amount, so the light has big influence to the shooting effect.  
BlueEyes Technology  
12  
www.BlueEyes.tw  
 
 
 
The more the light come in, the better the shooting is.  
We advise you to turn the IRIS to maximum to get enough light.  
If you use digital board or projector, you can adjust the IRIS to maximum then  
close down gradually.  
The light should be the same as class time.  
Fasten the nut after adjusting.  
When adjusting the camera lens, try to arrange during the class because the light  
(
fluorescent light or sunshine) would influence the shooting.  
If the education institute records class in the evening, it is better for you to adjust  
lens in the evening.  
Steady light is very important for shooting.  
Use antidazzle lamp.  
Add antidazzle division.  
Replace to better light tube.  
The light on the blackboard must be the same.  
Use thick curtain to block sunlight. Turn on the light even it is daytime.  
W = Wide(wide angle/close)  
T = Tele(distance angle/far)  
The tips for adjusting is to make the left and right sides of the shooting scene  
justify both sides of the board, but when using scanner module, make the up and  
down sides of the shooting scene justify up and down sides of the board.  
Fasten the nut after adjusting.  
BlueEyes Technology  
13  
www.BlueEyes.tw  
 
 
←→  
=infinite, N=near-end  
The focus lock nut is close to the body, loosen it before adjusting.  
If you use digital board or projector, turn it on to adjust focus.  
The tips for adjusting is to write【正】in the center and four sides of the board.  
Adjust the focus to see the words clearly.  
Fasten the nut after adjusting.  
BlueEyes Technology  
14  
www.BlueEyes.tw  
 
The lens is imported from Japan, it is very expensive.  
BlueEyes Technology  
15  
www.BlueEyes.tw  
 
 
Do not touch the lens during construction.  
We would cover a dust cover on the lens, and please do not remove it until  
adjusting.  
If you find the lens have dust or fingerprint  
Please blow the dust away with [lens blower] first  
Then wipe the lens clockwise from center to the outer with [lens pen]  
Do not blow with mouth or wipe with tissue.  
Do not remove the lens. This may make the lens stained with  
dust and fingerprint.  
BlueEyes Technology  
16  
www.BlueEyes.tw  
1
.
You can set the settings in “video”. Click “yes” to complete the setting.  
Key functions:  
Camera  
Default is iCam.  
BlueEyes Technology  
17  
www.BlueEyes.tw  
 
 
iCam  
Specifies the name of the IP Camera.  
Default is Dual H.264.  
Codec  
Choose the video format fromH264」、「 MJPEG.  
Default is 1920x1080.  
Resolution  
This option allows the user to choose the video resolution of the camera:  
1920x1080」、「1280x1024」、「1280x720」、「 640x480.  
Length and lenient  
Image frames  
GOP  
Default is OFF.  
Default is26fps  
Click on IP Camera to choose the frame rates of 1~60fps in all resolution.  
Default is 30」  
Default is CBR.  
Set CBRorVBR」  
OFF: MPEG4 will be coded with QP = 4 H264 will be coded with QP = 28  
VBR: Variable Bit rate.  
Rate Control  
CBR: Constant Bit rate. This will have frame skips to maintain bit rate with  
specified VBV buffer.  
Notice!! For Recording: CBR, For Live Video: VBR!!  
Default is 4000kbps.  
Type the required bit-rate for both MPEG4 Setting and H.264 Setting. Bit-  
rate values ranges between 64 and 10000 from stream1 and 64 to 8000 for  
stream2/stream3.  
Bit Rate  
Overlay Setting  
Mirror  
Select Enable Date and Time check box to activate the function.  
Default is OFF.  
Select the required option: HORZONTALVERTICAL and BOTH.  
Default is NTSC.  
Local Display Video  
Watermark  
Select one of the following options of the display device:NTSCan d PAL.  
Default is OFF.  
Select the required option: Position X, Position Y, transparency.  
iCam PRO is set already. Do not edit the default unless you  
are trained and understand the way and the meanings of  
editing.  
We recommend using Microsoft Internet Explorer version 10  
or higher web browser.  
BlueEyes Technology  
18  
www.BlueEyes.tw  
 
BlueEyes Technology  
19  
www.BlueEyes.tw  
Key functions:  
Default is iCam PRO.  
Camera  
Enter the name of IP Camera.  
Default is 128.  
Select the required brightness level that ranges from 0 to 255. .  
A brighter scene appears, if you choose higher level of  
brightness.  
Brightness  
Default is 128.  
Contrast  
Select the required range. The range available is from 0 to 255.  
Default is 128.  
Saturation  
Select the required saturation level that ranges from 0 to 255.  
A vivid scene appears, if you choose a higher level of saturation.  
Default is 128.  
Sharpness  
Select the required range of sharpness. The range available is  
from 0 to 255.  
Default is 128.  
Hue  
Select the required range of hue. The range available is from 0  
to 255.  
Default is OFF.  
Back Light Compensation  
Select one of the following options to turn on/off the backlight  
function  
Default is OFF.  
Enable WDR  
WDR Level  
The Wide Dynamic Range (WDR) function  
Default is 5.  
Select your options of the level between 1 and 10  
Default is 60Hz.  
Select one of the following options of the Flicker device  
NTSC/60Hz : This will compensate for 60Hz flicker and will put  
the display if selected to NTSC mode  
Flicker Control  
Color Mode  
PAL/50Hz : This will compensate for 50Hz flicker and will put  
the display if selected to PAL mode  
Default is Day.  
Select your option from Auto, Day, and Night.  
Default are On, Shutter 1/60 sec, Gain 25  
Static  
DNR  
if image is too dark try increasing gain value!!  
Default is ON.  
Default is OFF  
Protocol  
Select your option from OFFPelcoPPelcoD.  
Default is 1  
Device ID  
Baud Rate  
Select your options between 0 and 1.  
Default is 2400  
Select your option from 120024004800960019200.  
BlueEyes Technology  
20  
www.BlueEyes.tw  
Default is 16  
Speed  
Select your options between 0 and 23.  
Default is 0  
Min Move Time  
Select your options between 0 and 1.  
Default is OFF  
Privacy  
Blocking a specific area on the monitor for the protection of  
individual privacy.  
Default is N/A.  
Booting LED  
Select your options N/A, Red, Blue, Purple.  
We recommend using Microsoft Internet Explorer version 10  
or higher web browser.  
In order to protect the privacy of the students in the front rolls who shown  
in the video, we develop the “Privacy Mask Setting.” You can choose three  
areas where students’ faces appear, then the area you choose would not  
appear on the video. The steps of setting are as below:  
1
. Login camera IP, and enter camera account and password.  
2
. Click camera in the setting column.  
BlueEyes Technology  
21  
www.BlueEyes.tw  
 
3
4
. Select the checkbox to enable privacy mask.  
. After enabling privacy mask, set the monitor from right to left and click “set”.  
5
. You can set three ranges of the privacy mask which represent by red, green and  
blue.  
BlueEyes Technology  
22  
www.BlueEyes.tw  
6
7
. You can click “clear” to cancel the privacy mask.  
. You can watch the live view to check the range of the privacy mask.  
BlueEyes Technology  
23  
www.BlueEyes.tw  
We recommend using Microsoft Internet Explorer version 10  
or higher web browser, and do not join the "Compatibility  
View Settings".  
1
.
Enter “Audio” setting to adjust audio input and output. Click “Accept” to  
save the setting.  
Key functions:  
Default is ON.  
Enable Audio  
This will switch ON/OFF the audio in camera.  
Default is only Mic.  
You can change the audio mode in the Network camera in one  
of the following ways:  
Audio Mode  
Input Gain  
Only Mic: Enables only audio capture in camera.  
Only Speaker: Enables only audio playback in camera.  
Both Mic & Speaker: Enables both audio playback & capture in  
camera.  
Default is 0.  
Sets the input capture gain, values set from 1-60.  
Encoding  
Channels  
Sample Rate  
Bit Rate  
Default is PCM.  
Default is 2(stereo).  
Default is 44.1Khz.  
Default is 32k bps.  
BlueEyes Technology  
24  
www.BlueEyes.tw  
 
We recommend using Microsoft Internet Explorer version 10  
or higher web browser.  
Follow the steps to adjust network setting and IP address. Click “Accept to  
save the setting.  
Key functions:  
If you have a DHCP server running on your network and  
would  
DHCP  
like a dynamic IP address to be updated to your camera  
automatically.  
Specifies the IP address of the camera. Options include: IP  
Static IP  
address, Subnet mask, Gateway and MTU.  
Support users use IP of ADSL to connect with internet when  
connect from internet.  
PPPoE  
DNS Assignment  
Specifies the DNS server for your network.  
Primary DNS Server  
Secondary DNS Server  
Network of preferred and alternate DNS server address.  
Network of preferred and alternate DNS server address.  
BlueEyes Technology  
25  
www.BlueEyes.tw  
 
We recommend using Microsoft Internet Explorer version 10  
or higher web browser.  
Please make sure “sync with NVR” is “any one”.  
EPTZ only support dip 1280*720.  
BlueEyes Technology  
26  
www.BlueEyes.tw  
 
Many education institutes want to mark their name on the videos. You can  
upload the trademark and name on iCam PRO.  
Click  
the instruction below to open Paint.  
systemroot%\system32\mspaint.exe  
+R or [Start]  [implement] to open the implement window. Enter  
%
Make a trademark in Paint.  
Save asBMP pictureFile type24 bitmap】!Important!  
Use IE browser to connect to iCam1080 network management. Click  
[
Watermark] in [Maintenance]. Here are the steps:  
Step 1:  
ClickChoose file to choose your watermark picture.  
BlueEyes Technology  
27  
www.BlueEyes.tw